- Nameplate
- Operating file
- Pressure equipment
Illegible nameplate: rebuilding pressure equipment data
Missing, rusted or painted-over nameplate: where to find the PS, TS, volume and serial number of pressure equipment, in what order, and when to stop.
By cDESP team5 min read
The case every refrigeration technician has met
A liquid receiver at the back of a machine room, a nameplate covered by three coats of paint, or simply torn off when the insulation was replaced. The file contains nothing. And yet, without PS or volume, there is no way of knowing whether the equipment is subject to in-service monitoring, or of classifying it correctly in the list.
The temptation to estimate is strong. That is precisely what you should not do. The characteristics of pressure equipment (ESP, équipements sous pression) are design data set by the manufacturer: the maximum allowable pressure PS is, according to article 2 of Directive 2014/68/EU (the Pressure Equipment Directive, PED), the maximum pressure for which the equipment is designed, as specified by the manufacturer. It cannot be deduced from the operating pressure or from the relief valve set pressure.
The right approach is to find the information in reliable sources, in a logical order, and to record where each value comes from.
What the nameplate should have shown
Point 3.3 of Annex I of Directive 2014/68/EU lists the information to be affixed to the equipment or to a firmly attached nameplate. It includes in particular:
- the year of manufacture;
- the identification of the equipment (type, series or batch identification, serial number);
- the maximum and minimum allowable limits (PS, TS);
- depending on the type of equipment: the volume V or the DN, the test pressure PT and its date, the fluid group, the set pressure of the safety device...
Added to this are the CE marking and, where a notified body was involved in the production control phase, its identification number. That is the list of what you are trying to reconstruct.
The sources, from the most reliable to the least direct
1. The instructions
This is the best lead, and the directive guarantees it: according to point 3.4 of its Annex I, the instructions must contain the information affixed to the equipment, except the series identification. If the instructions exist somewhere (installer's file, engineering firm archives, machine room cabinet), they should in principle contain PS, TS and V.
2. The EU declaration of conformity
Its model, in Annex IV of the directive, provides for the identification of the equipment (product, type, batch or serial number), the conformity assessment procedure applied and, where applicable, the notified body. For a refrigeration assembly, look for the declaration of the assembly and the list of the equipment it comprises.
3. Operating documents already produced
They often repeat the nameplate data, recorded when it was still legible:
- previous periodic inspection reports and requalification certificates;
- the commissioning declaration and its proof of filing for the equipment that was subject to it;
- an earlier equipment list, commissioning photos, initial verification reports;
- the inspection plan, which identifies each item of equipment covered.
Caution: a secondary document may itself contain a copying error. Cross-check at least two sources when possible.
4. The manufacturer
With a serial number, even a partial one, the manufacturer can often find the file. The directive requires the manufacturer to keep the technical documentation and the EU declaration of conformity for ten years after the equipment has been placed on the market (article 6 of the directive). Beyond that, nothing is guaranteed, but many manufacturers keep archives longer. The serial number is sometimes stamped directly on the shell, a head or a flange, even when the nameplate has disappeared: look for it before concluding it no longer exists.
5. The installer or assembler
They ordered the equipment: purchase orders, selection sheets, layout drawings, refrigeration diagram with tags. These documents make it possible to identify the exact model, and then to trace back to the manufacturer.
What not to do
- Deduce PS from the relief valve set pressure. The arrêté du 20 novembre 2017 (French ministerial order of 20 November 2017 on in-service monitoring of pressure equipment) requires a safety accessory to be set at most at PS (article 3), but a lower setting is possible. The set pressure only gives you a lower bound, not PS.
- Measure the volume with a ruler and record it as V. The volume within the meaning of the directive is an internal design volume, including connections up to the first connection. A geometric estimate can help with a first sort, never replace the manufacturer's data.
- Copy the data from an "identical" item of equipment. Two vessels that look alike can have different PS values, particularly between high and low pressure.
- Engrave a new nameplate yourself. An internal tag (label, QR code) helps with identification on site, but it does not replace the regulatory marking.
When nothing can be found
Sometimes every lead fails. At that point, it is no longer a matter of document research but a technical and regulatory decision, to be taken with your competent person (personne compétente) and your authorised inspection body (organisme habilité). For equipment built under French regulations predating CE marking, the order provides for a descriptive statement "initial or reconstructed under conditions specified by a decision of the minister" (article 6). For CE-marked equipment whose characteristics can no longer be established, the solution depends on the case: it needs to be examined with the authorised inspection body, which will tell you what it can accept for in-service monitoring. Replacing the equipment is one of the options to weigh up.
In all cases, do not leave the row empty in the list: write "data to be reconstructed", the date of the finding and the action in progress.
Recording the reconstruction
Each value found must be justifiable. In the operating file (dossier d'exploitation), keep:
- the photo of the condition of the nameplate at the time of the finding;
- each source used, with its date and origin;
- the table of values retained and the source of each one;
- the validation by the competent person, and the opinion of the authorised inspection body if you asked for it;
- the entry of the operation in the log.
Prevent rather than reconstruct
The best reconstruction is the one you do not have to do. Three habits are enough:
- photograph each nameplate at commissioning, and at each inspection if its condition deteriorates;
- demand the instructions and the declaration of conformity at acceptance of the installation;
- protect nameplates during painting or insulation work, and keep them accessible for reading.
With cDESP
In cDESP, a photo of a legible nameplate is enough to prefill the characteristics of the equipment thanks to automatic reading, and the photo is kept with the equipment. CE declarations and instructions are attached to the equipment models, which avoids searching for them site by site. For a nameplate that is already lost, the tool will not guess anything for you: it helps you organise the sources and record the decision.
To start photographing and filing your nameplates, create an account or see the pricing.